KiCad PCB Design· Live
Home / Chapter 2 / 2.4

USB-C connector symbol and footprint

Lesson 2.4 · KiCad · free

The last part is a power-only USB-C connector, the Amphenol 10164359-00011LF. It has no data lines, it only brings 5 V to the board, so the design stays simple.

The big picture
  1. Datasheets
  2. Symbols & footprints
  3. Schematic
  4. PCB layout
  5. Files & order

The last part in our library: the USB-C connector, where the 5 V comes into the board. After this lesson every part has a symbol and a footprint, so in chapter 3 we can draw the schematic.

Datasheets

Want the ready USB-C symbol and footprint?

The full course includes the Steppeschool KiCad library: every symbol, footprint and 3D model from this course, plus the whole project (schematic, PCB, Gerbers). Members download it from the Project Files lesson on the course page. Not a member yet? Get the full course (from $5).

In this lesson · 5 steps
  1. Read the connector drawing
  2. The symbol
  3. SMD pads
  4. Through-hole pads
  5. Courtyard, silkscreen, 3D model

1Read the connector drawing

The drawing gives the pad positions; the pin table gives the meaning of each pad.

  1. From the product page, open the drawing: six SMD pads and four through-hole pads
  2. The pin assignments: A5 CC1, A9 VBUS, A12 GND, B12 GND, B9 VBUS, B5 CC2. We number the pads 1–6 from the left

2The symbol

Seven pins: power, ground, the two CC pins we need in chapter 3, and the shield.

  1. New symbol 10164359-00011LF, reference USB
  2. Pins 1 GND, 2 VBUS, 3 CC1, 4 CC2, 5 VBUS, 6 GND, 7 SHIELD
Why?
The datasheet doesn't list a pin for the metal body, but it exists. We add pin 7, SHIELD, so the body can go to ground.

3SMD pads

The SMD pads carry the power and the CC signals.

  1. Six pads 0.8 × 1.2 mm at x = ±0.5, ±1.52, ±2.75 mm
Why?
We put the origin in the middle of the connector. The pads are symmetric, so each position on the left has a twin on the right.

4Through-hole pads

The through-hole pads hold the connector firmly when you plug in the cable.

  1. New pad → Pad type Through-hole, number 7 · Hole: Oval 0.6 × 1.2 mm · Pad: rounded rectangle 1.1 × 1.7 mm, corner 50 %
  2. Four of them at x = ±4.32 mm, y = 0 and 3.8 mm

5Courtyard, silkscreen, 3D model

With the courtyard, the 3D model and the link, the connector is ready for the schematic.

  1. Draw the courtyard and a few silkscreen lines for the body → rename the footprint 10164359-00011LF
  2. Add the STEP model, rotate X -90°, offset Y -3 mm until it lines up → save
  3. Symbol Editor → Footprint: 10164359-00011LF; fill Datasheet, Description, Manufacturer Amphenol ICC (FCI) and Part Number → save
Check & troubleshoot

What you should see

  • Symbol pins: 1 GND, 2 VBUS, 3 CC1, 4 CC2, 5 VBUS, 6 GND and 7 SHIELD
  • Six SMD pads 0.8 × 1.2 mm
  • Four through-hole pads 7: 1.1 × 1.7 mm, oval drill 0.6 × 1.2 mm
  • The 3D model lines up with all the pads

If it doesn't work

  • Through-hole pad shows no hole: set Pad type to Through-hole, not SMD
  • Round hole instead of a slot: set the hole shape to Oval and give two sizes
  • Pins 2 and 5 (or 1 and 6) look like duplicates: that's right. The connector has two VBUS and two GND pins, one for each plug orientation

Good to know

  • Through-hole pads go through the board. When you plug and unplug a cable, they take the force, so the connector doesn't break off
  • SMD pads are easier to assemble by machine. Through-hole pads are often soldered by hand and take longer
  • We number the pads 1 to 6 from the left instead of the A/B names. Simple, and the pin table tells us each one's function

Next: Chapter 3: we connect all our parts in the schematic.